
VGI-DWC4
Image | Name | Quantity |
---|---|---|
DWC Hydroponic Bucket |
1 pc |
|
Seedling Planting Basket |
1 pc |
|
Planting Basket |
2 pcs |
|
Air Stone |
2 pcs |
|
Rapid Rooter |
2 pcs |
Durable Build :Made from high-quality polypropylene for enhanced strength and long-lasting durability.
Maintenance Window :The specially designed gridded maintenance window opens and closes easily, allowing you to add water or test pH and EC levels.
Large Tank Capacity :The 4 gal / 15 L water reservoir automatically supplies your plants with water and nutrients, providing consistent hydration and nourishment.
High Oxygen Content :The dual air stone design maintains high oxygen levels to help prevent root rot.
Grow Faster :Use Rapid Rooter to promote strong early rooting and support vigorous plant growth.
Active Monitoring :Includes a water meter and temperature sensor to help you monitor your nutrient solution.
Dimensions |
17.2*17.2*8.6 inch (43.6*43.6*21.9 cm) |
Tank Capacity |
4 Gal (15L) |
Water Pump |
DC 5V, 2W, 160L/h |
Air Pump |
DC 5V, 4W, 2*2000ml/min, 20KPA |
Drain Pipe |
39 inch (1m) |
Air Stone |
Φ2.4 inch (Φ6cm) |
Place the two air stones in the allocated positions.
Connect the air tubes as shown in the diagram.
After placing the DWC Hydroponic Bucket lid, open the water inlet and pull out the drain pipe.
Clip the drain pipe to the back of the water inlet as shown in the diagram.
Place the DWC Hydroponic Bucket securely into your VGrow.
Plug in the water level sensor.
*① Smart Top Cover
Pour the nutrient solution through the water inlet.
Do not exceed the maximum water level, as indicated in the diagram.
Remove the drain pipe from the back of the water inlet.
Secure the drain pipe to a waterproof container.
Press the drain button to start draining.
Note: To prevent overflow from being left on too long, the water pump will automatically stop every 2 minutes. Please press the drain button again after it stops to resume draining.
To Install:
Align the control box with the lower right corner of the DWC Hydroponic Bucket.
Gently lower it downward until it clicks into place.
To Remove:
Lift the control box upward, as shown in the diagram.
Using the paper towel method for seed germination, keep the towel moist and place it in a dark environment at 70–80°F. Seeds typically sprout within 1–2 days.
First, soak the Rapid Rooter in nutrient solution until fully saturated. The pH should be between 5.5–6.5, and the EC should be 0.5 mS/cm (250 ppm). Next, insert the germinated seeds about 0.2 inches deep into the Rapid Rooter. Place the Rapid Rooter into the Planting Basket, then into the Seedling Planting Basket, and insert them into the DWC Hydroponic Bucket. Set the VGrow recipe to “Seedling Mode.” If available, cover the seedlings with a dome to maintain humidity. Ideal conditions: temperature at 77°F; humidity between 70–80%. Seedlings typically emerge within 1–2 days.
Note: At this stage, there is no need to add nutrient solution to the hydroponic bucket.
Duration: 7–14 days
Temperature: 77°F
Humidity: 70–80%.
Check the moisture level of the Rapid Rooters daily. If they become dry, replenish with nutrient solution (pH 5.5–6.5; EC 0.5 mS/cm).
When the plant has developed two sets of true leaves and the roots have penetrated the Rapid Rooter, it is ready to transition to the Vegetative stage. Remove the Seedling Planting Basket from the DWC Hydroponic Bucket and place the Planting Basket back into the DWC Hydroponic Bucket. Prepare the nutrient solution and fill the reservoir with 4 gallons of solution.
Vivosun Nutrients Feed Chart For DWC |
|||||||||||||
Stage of Growth |
Seedling/Clone |
Vegetative |
Flowering |
||||||||||
Week |
1-2 |
1 |
2 |
3 |
4 |
1 |
2 |
3 |
4 |
5 |
6 |
7 |
8 |
Base A 4-0-1 (ml/gal) |
1-2 |
2.5 |
3.5 |
3.5 |
4.5 |
4.5 |
6 |
7 |
7 |
5 |
5 |
3.5 |
3.5 |
Base B 1-4-2 (ml/gal) |
1-2 |
2.5 |
3.5 |
3.5 |
4.5 |
4.5 |
6 |
7 |
7 |
5 |
5 |
3.5 |
3.5 |
NutriBoost 0-0-1 (ml/gal) |
1 |
1~2 |
1~2 |
1~2 |
1~2 |
2~4 |
2~4 |
2~4 |
2~4 |
2~4 |
2~4 |
2~4 |
2~4 |
Bloom Juice 0-6-4 (ml/gal) |
0 |
0 |
0 |
0 |
0 |
1 |
1 |
2.5 |
2.5 |
3.5 |
3.5 |
5 |
5 |
Cal+Mag+Iron 2-0-0 (ml/gal) |
1~2.5 |
1~2.5 |
1~2.5 |
1~2.5 |
1~2.5 |
1~2.5 |
1~2.5 |
1~2.5 |
1~2.5 |
1~2.5 |
1~2.5 |
1~2.5 |
1~2.5 |
PPM |
145-235 |
240~320 |
330~405 |
330~405 |
400~440 |
405~450 |
480~560 |
565~645 |
565~645 |
430~515 |
430~515 |
375~420 |
375~420 |
EC |
0.3~0.5 |
0.5~0.6 |
0.7~0.8 |
0.7~0.8 |
0.8~0.9 |
0.8~0.9 |
1.0~1.1 |
1.1~1.3 |
1.1~1.3 |
0.9~1.0 |
0.9~1.0 |
0.7~0.8 |
0.7~0.8 |
pH |
5.8~6.2 |
5.8~6.2 |
5.8~6.2 |
5.8~6.2 |
5.8~6.2 |
5.8~6.2 |
5.8~6.2 |
5.8~6.2 |
5.8~6.2 |
5.8~6.2 |
5.8~6.2 |
5.8~6.2 |
5.8~6.2 |
This chart is for water starting with a PPM level of zero. For each 50 PPM level of hard water you start with, your EC will rise by 0.1. This is based on the PPM x 500 scale.
Instructions:
It is recommended to use at least the Base Nutrients solution each time you add water, and to adjust the pH to between 5.8 and 6.2.
When using RO water, it is recommended to add a Cal-Mag additive.
If your plant variety requires additional growth weeks, repeat the nutrient concentration from flowering week 8.
This is a baseline recommendation. Please adjust the nutrient solution concentration based on the plant variety, growth conditions, environmental factors, and other variables.
It is recommended to change the nutrient solution once a week.
Please add nutrient solution promptly when the low water alert is triggered.
Prepare the nutrient solution according to the instructions provided with the product.
It is recommended to replace the nutrient solution once a week.
When the low water level alarm is triggered, promptly refill to the maximum water level line with nutrient solution.
Do not stand on the product.
Do not add water beyond the maximum water level line. Water must not enter the control box.
Perform a test run with clean water to ensure the air pump and pipelines are functioning properly.
Perform regular maintenance to prevent the growth of algae or bacteria.
If the product is damaged, stop use immediately and contact us for support. Disassembly or modification without Vivosun’s express permission will void the product warranty.
DO NOT dispose of this product with regular household waste. Electrical appliances contain hazardous materials that can harm the environment if not handled properly.
Please contact your local authorities for information on nearby drop-off centers or approved recycling programs that accept electronic waste.
Vivosun provides a 2-year warranty against defects on all VGrow DWC Hydroponics Grow Kit products purchased directly from us or through our authorized dealers. This policy serves as our commitment to promptly address any manufacturing defects or premature breakage that may occur during normal use.
Our warranty covers the replacement or refund of purchases that exhibit material defects within two years of the original purchase date. In such events, customers may contact us to initiate the claim process. We will need proof of purchase to verify coverage eligibility.
This policy does not extend to products that have been misused, abused, or purposefully damaged. It also does not cover normal wear and tear or cosmetic defects such as minor scratches.
Customers can rest assured knowing that our products undergo rigorous quality testing procedures. This 2-year warranty reflects our confidence in the durability of our products under normal use.If any product defects are found, customers are encouraged to contact us immediately. Your satisfaction is our top priority, and we are committed to resolving any issues in a professional and timely manner.